Updated Nov 19, 2026· 5 min read

Key takeaways

  • The Mounting Dream MD2380 full motion TV wall mount tilts, swivels and extends for 32 to 70 inch TVs. Check VESA fit, stud spacing and arm reach.

A full motion wall mount lets a television turn toward different seats, tilt down toward a sofa, or pull away from the wall for cable access, which a flat fixed bracket cannot do. The Mounting Dream MD2380 is an articulating dual-arm mount built around that flexibility for mid-size and large flat screens.

This review covers the screen sizes and VESA patterns it fits, how far the arms extend and swivel, and the wall requirements that decide whether it can be installed safely. Those installation details matter more with a moving mount than headline size ranges, because the arms place changing loads on the wall fixings.

As an Amazon Associate, we earn from qualifying purchases.

Quick answer

The Mounting Dream MD2380 is a full motion TV wall mount for most 32 to 70 inch flat TVs, with VESA patterns from 75×75 to 400×400 mm. Dual articulating arms extend to 17.5 inches, tilt from plus 5 to minus 15 degrees and swivel, and the mount fits 16 inch wood stud spacing.

Key specs

Spec Detail
Model MD2380
Screen size fit Most 32-70 in LED, LCD and OLED flat TVs
VESA compatibility 75×75 to 400×400 mm, max VESA 400×400 mm
Tilt range +5 degrees to -15 degrees
Swivel Left and right, up to 45 degrees per listing copy
Extension Extends out to 17.5 in, retracts to about 3.4 in from the wall
Wall fit 16 in wood-stud spacing; wood stud or concrete wall only
Construction Articulating dual arms, black metal
Weight capacity not stated

Check price on Amazon

Design and everyday use

The MD2380 uses two articulating arms rather than a single arm. Dual arms spread the load across the wall plate and tend to keep a large screen steadier when it is pulled out or turned, which matters most at the larger end of the supported size range. Pushed back, the television sits about 3.4 inches from the wall, and pulled forward it reaches 17.5 inches out, enough to turn the screen toward a side chair or to reach ports on the back panel.

Tilt runs from 5 degrees up to 15 degrees down. The downward range is the one used most often, for sets mounted above a fireplace or on a high wall viewed from a low sofa. Swivel is listed at up to 45 degrees, which in practice depends on screen width: a wider television will meet the wall sooner when turned, so the usable angle shrinks as screen size grows toward the top of the range.

VESA compatibility covers patterns from 75×75 mm up to 400×400 mm, which spans the mounting holes found on most televisions in the 32 to 70 inch range. Checking the pattern on the back of the actual set is still essential, because some large screens use wider patterns than 400×400 mm, and those will not fit this mount regardless of screen size.

Installation is limited to wood stud walls with 16 inch spacing or to concrete walls. The listing is explicit that the mount should not be fixed to drywall alone, which is a real constraint for rooms where the viewing wall is a partition or where studs fall in the wrong place for a centred screen. The wall plate is sized around that 16 inch stud spacing, so measuring the wall comes before ordering.

Day to day, a full motion mount earns its space when seating is spread out, when glare from windows needs to be angled away, or when the television shares a room between viewing positions. For a single sofa directly in front of the screen, most of the articulation goes unused after setup, though the extension still helps for cable changes.

Who it’s for / who should skip

This mount suits owners of 32 to 70 inch televisions with VESA patterns up to 400×400 mm who watch from more than one position, or who mount the set high and need downward tilt. It also fits households that change cables or devices behind the television often, since the 17.5 inch extension gives working room at the back panel.

It should be skipped by anyone whose wall is drywall without accessible studs, whose stud spacing differs from 16 inches without a workable mounting position, or whose television uses a VESA pattern wider than 400×400 mm. Shoppers who want the screen almost flush to the wall should look at low-profile fixed mounts instead, since this design sits about 3.4 inches out even when retracted. The supported weight capacity is not stated in the verified data used here, so buyers should confirm the rating against their television’s weight on the product page before installing.

How it compares with alternatives

Compared with fixed flat mounts, the MD2380 adds tilt, swivel and extension at the cost of a deeper profile and a more involved installation. Compared with tilt-only mounts, it adds the ability to turn the screen toward side seating and to pull it forward for access, which tilt-only designs cannot do.

Against single-arm full motion mounts, the dual-arm layout generally suits larger, heavier screens in the range better, because the load is shared across two arms, while single-arm designs can feel more flexible with smaller sets. Against ceiling or corner-specific mounts, this is a conventional wall design that assumes a flat wall and standard stud construction.

FAQ

Which televisions fit the Mounting Dream MD2380?

It fits most 32 to 70 inch LED, LCD and OLED flat TVs with VESA mounting patterns between 75×75 mm and 400×400 mm. The VESA pattern on the back of the set is the deciding check.

What walls can the MD2380 be mounted on?

It is made for wood stud walls with 16 inch spacing or for concrete walls. The listing states it should not be installed on drywall alone.

How far does the television sit from the wall?

Retracted, the screen sits about 3.4 inches from the wall. The dual arms extend out to 17.5 inches for viewing angle changes or access to the back of the set.

How much weight can this mount hold?

The weight capacity is not stated in the verified product data used for this review, with figures varying between sources. Check the current product page for the confirmed rating before mounting a television.

Final verdict

The Mounting Dream MD2380 covers the core full motion brief: a wide VESA range, useful tilt and swivel, and a long 17.5 inch extension on dual arms. Its conditions are equally clear: a stud or concrete wall, 16 inch stud spacing, and a set within the VESA limit. Buyers who confirm those points, and who verify the weight rating for their own television, get a flexible mount for multi-angle viewing rooms.

A
admin
We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.
Mounting Dream MD2380 TV Wall Mount Review for…Check price on Amazon